The Altair TMS Ultra Light Guide Scope Rings are available in 120mm or 150mm sizes. They have a lightweight design unique to Altair Astro, which results in a far lighter guide scope ring, while still maintaining strength and rigidity.
The Altair TMS uses durable all stainless steel M8 threads - that means they will not corrode, unlike cheaper makes which use low grade blackened steel threads and screws, which eventually go brown with rust. The Altair Telescope Mounting System (TM) is more durable than any other product on the market we've seen.
This new Clear Silver colour goes well with any telescope, is arguably easier on the eye than black, and goes very nicely with our blue hardware range. Sure, telescopes are meant to be used in the dark - but there's no harm in your setup looking attractive too! A full Altair Telescope Mounting System is a thing to behold!
Check out this customer review of the earlier non-lightweight Altair TMS Guide Scope Rings (opens new window).
Direct bar or plate mounting: The Altair Guide Scope Rings are unique (at least at the time we write this) because they can be mounted on the top or bottom of Altair Losmandy-format or Vixen-format bars via two M6 bolts on each ring, to stop them twisting like other makes with single bolts. All Altair TMS Losmandy plates or Vixen bars have this two-hole pattern, and you can adjust the separation of the rings by choosing different holes along the length of the plate. GSR rings have flattened edges for good contact with the bar or plate they're fastened to and are far more rigid than any other guidescope rings we have seen to date.
Direct clamp mounting: GSR rings can also be mounted on Altair TMS Small Vixen Clamps or Losmandy Saddle Plates to slide back and forth to achieve the best balance. This is perfect for Altair Astro RCs and Meade and Celestron SCT telescopes with an inverted rail on top. (see picture below)
The GSR benefits from easy-grip hard anodised knobs, custom-machined for a positive grip (we tested several iterations). They are very easy to un-tighten and adjust, even with gloves on.
Each thread has a plastic end cap to give a more forgiving contact with your optical tube without causing movement. This is better than soft rubber end caps, which change compression with temperature and cause movement, often splitting after a year or so of use.
Altair TMS is made in the UK at our local machine shop on HAAS CNC milling machines, which means we have complete control over quality. Each part is hand polished before anodising to remove burs and give a smooth finish. The quality level and material means a slightly higher price than budget rings. Recommended for those who want the best.
The Astrolift 150 is a motorised lifting pier manufactured and assembled by HiTec Astro.
The pier has a maximum load bearing capacity of 150kg.
Minimum and maximum useable heights are 70cm and 110cm. The unloaded pier weighs 22kg.
The Lifting Pier 150 ships with a Universal Pier top that accepts the following mounts directly
In addition It will also accept the Altair Multi Mount Pier Adaptor and EQ8 Pier Adaptors.
The Lifting Pier ships with a mains to 12v power supply.
the bottom plate has 4 radius corners to help with plar alignment after the pier has been afixed to the observatory floor.
The USP is a heavy duty saddle plate which is designed to replace the factory clamps on equatorial mounts with a more rigid and precise alternative for imaging or visual use with heavier telescopes. It's not only easier to use, it's also safer and stronger than the factory clamps you get with your mount. The Altair USP is compatible with both the Vixen/Synta-format telescope mounting bars, or the Losmandy-format wider mounting plates. This all-in-one design means you don't have to change clamps for different telescopes, making your mount more compatible.
The USP fits most medium sized equatorial mounts on the market including the iOptron iEQ45, Losmandy G11 and the Skywatcher EQ6, Orion USA Atlas or Skywatcher HEQ5. The Universal Saddle Plate or "USP" is also compatible with the rest of the Altair TMS Telescope Mounting System accessory range.
This is the black anodized version of the Altair USP, and it goes very well with any colour of mounting hardware, including silver and blue.
Altair Heavy Duty USP Features:
Compatible with Losmandy-wide-format dovetail plates, and Vixen-narrow-format doevtail bars. Very precisely machined.
Safe and easy "tip in" saddle lets you place your telescope quickly and easily from the side, while tightening up the clamps with your other hand. This avoids that awkward struggle in the dark, while you try to hold onto a damp slippery telescope, while carefully lining up a saddle plate which will only slide in from the very end. This design feature is now much-copied and is based on feedback and requests from several customers who have nearly dropped their telescopes!
Chamfered and rounded edges make it even easier to get a heavy telescope placed securely, before tightening the clamps with your other hand.
Heavy duty hard anodised star knobs, custom-machined for a positive grip with or without gloves.
The clamp has machined guides for a positive lock.
No sharp edges or poor machining.
The heavy duty spring loaded Stainless Steel M8 threads do not corrode.
Looks great in hard anodised "Altair Blue" to match the rest of the TMS range.
Readily available, and made locally in the UK at our machine shop on HAAS 4 axis CNC milling machines. That means we have complete control over quality.
The new Altair Astro CNC machined aluminium pier adapter is used to secure the following Equatorial mounts to your Altair SkyShed Pier:
Altair Sabre mount
Skywatcher EQ6 (AKA Orion Atlas)
Celestron CG-5 & CG-4
Generic Chinese EQ5 mounts such as "Astro-5 EQ" mount
Meade LXD75 (due to mount model variations, please email us to confirm dimensions)
Several Vixen mounts (due to mount variations, please email us to confirm dimensions)
Other mounts: The pier adapter also fits several other mounts including those made by Meade and Vixen Japan, however we request you email us dimensions so we can confirm because there are some variations in these mounts depending on the year of manufacture.
The pier adapter has four recessed holes around the outer perimeter for fastening it to the pier plate in various positions.
The pier adapter is designed to add 32mm height to the mount in order to clear the pier top plate.
4x corrosion resistant stainless steel bolts and nuts are included with your pier adapter for quick and easy installation. The pier adapter is clear silver anodised.
Using the Azimuth (rotation) stop for each type of mount:
You'll notice a "stop bolt" protruding from your equatorial mount field tripod. This is to provide something for the azimuth rotation adjustment screws to push against for fine adjustment, and polar alignment. (Some older CGE and EQ-5 mounts also have a cast metal "nub" which protrudes from the tripod head).
There is an additional threaded hole for the EQ6 azimuth stop bolt which protrudes from the field tripod. If you do not intend on using your mount and tripod in the field very often, you can just unscrew the azimuth stop bolt on your tripod, and screw that into the pre-threaded hole on the adapter.
You can also use your own M8 bolt instead of the bolt from your tripod. This will not affect your mount performance.
Product feature summary:
Transfer your EQ mount from static pier to field tripod in minutes.
CNC machined from solid aluminium, anodised to ensure corrosion protection.
4x corrosion resistant stainless steel nuts & bolts are included.
Fits the Altair/SkyShed 8” Steel Adjustable Pier without any drilling.
The existing hole pattern on Altair Piers is the same as the Meade LX200.
The Altair pier adapter be used on any flat surface with the correct holes, such as a home made pier of your own.
Pleasing to the eye in anodised aluminium, complementing the crisp lines of the laser-cut 8” Altair-SkyShed Pier and the Altair TMS product range.
The Altair Vixen-format dovetail bars are narrow and light - the perfect option for small telescopes, for example a refractor of up to about 102mm or 4" aperture.
To mount two small telescopes with Vixen-format dovetail bar side-by-side, we recommend the Altair TMS "Small Vixen Dovetail Clamp" which is designed to bolt directly onto either end of our Vixen (or Losmandy) bars and plates with two bolts, giving maximum rigidity and strength. (If you order clamps with your bars, we'll include all the stainless steel bolts you need).
Optical tube separation: When using the 180mm Vixen-format dovetail bar to mount two optical tubes "side-by-side", they will have a centre to centre separation of 160mm. When using the 250mm Vixen-format dovetail bar you'll get 230mm centre to centre separation.
A countersunk M6 hole at each end, plus a countersunk centre M6 slot, allows maximum compatibility for attachment to most telescope tube rings on the market today.
Precision CNC machined locally, and hard black anodized for extra resistance to tarnishing or scratching. Altair TMS is a precision machined modular Telescope Mounting System. Our aim is to provide a simple, safe and rigid mounting system for most types of telescope on the market, to give our customers the best possible results for astro imaging and visual observing. All components can be re-used which makes the overall cost of ownership very cost effective in the loing run. Made from the highest grade British aerospace 6068 T6 tempered and artificially aged aluminium, which has the highest strength in the 6000 series alloy range and is extremely corrosion resistant. All threads are stainless steel, and dovetail clamps are spring loaded with teflon washers.
his Altair Astro CNC machined aluminium pier adapter is used to secure your Skywatcher EQ8 Equatorial mounts to your Starbase CNC field tripod, or your own pier top plate.
It's flat and smooth, with a large 200mm / 8" surface diameter, allowing easy rotation and more accurate polar alignment, and is clear-silver anodised.
Q: Why use this pier adapter instead of just bolting your mount to a pier directly? Most piers do not have a completely flat surface and the flatter and harder it is, the better for accurate polar alignment. Any bumps, distortions, or "soft spots" on the pier adapter surface will reduce the "repeatability" and smoothness during polar alignment.
Q: I have seen plastic, Delrin and Teflon lined pier adapters on the market, why is this all-metal surface better? An all-metal surface is better because plastics deform slightly under pressure (often non-linearly), and behave differently according to environmental factors, such as temperature and moisture content. If the surface of the pier adapter is made from a relatively hard metal surface, which is of similar hardness to the mount base (also aluminium alloy), so in this case aluminium is the ideal material. The material must be smooth and hard for smooth rotation so we mill the surface flat on a CNC machine. This is the reason why engineers use flat milled steel slabs on their workbenches upon which to measure and align metal objects.
Q: What is the hole pattern for attaching to my pier top? The "Altair Astro" standard pier top hole pattern is 6x 8mm ID holes, arranged with 130mm PCD
Q: Can I use this pier adapter with other piers? Yes of course. There is plenty of space to drill and tap your own holes on the large 8" flat surface as required.
6x cap-head stainless steel bolts are included to fit the threaded holes in your Starbase field tripod.
The entry level Starwave dual telescope mounting features a 3" centre dovetail bar, and two corresponding clamps, which attach directly to each end with the supplied hardware.
Optical tube separation when mounted side by side is approx 265mm centre to centre.
Compatible with Losmandy-format telescope mounting systems.
**Price Includes Carriage**
Now you can mount your wide field refractor of up to 80mm next to your autoguider unit, whilst keeping the centre of gravity as close to your mount as possible.
This is the ideal kit for someone starting imaging with a refractor up to 80mm. The perfect companion for the Starwave 70ED refractor and the iOptron ZEQ25 mount!
Starwave MiniGuider 60 Side-by-Side dovetail bar kit consists of:
The renouned Altair Astro 60mm Miniguider OTA, with special super-rigid locking focuser for your autoguider.*
Starwave 1.75" (44.45mm) width dovetail clamp to mount your refractor on one side.
The Starwave 200mm 1.75" (44.45mm) width Vixen-format dovetail plate which fits most portable mounts on the market today.
A set of mini guide scope rings with nylon tipped screws to mount on the opposite side of the dovetail bar, with connecting bar, to mount your 60mm Miniguider.
A set of M5 screws and nuts to mount the Miniguider 60 rings, and a set of M6 screws and nuts to mount the Starwave1.75" format clamp.
Can easily support refractors up to 80mm and will accurately guide up to at least 1000mm focal length without differential flexure.
Keeps your telescopes low and spaced widely enough apart such that the cables and autoguider unit can be adjusted easily without interfering with the main camera, unlike "piggyback setups". This is desirable when imaging with a DSLR enabling it to be easily rotated it when framing the subject. without fouling the autoguider unit.
The centre dovetail bar can be slid from side to side for easy balancing.
The Starwave Vixen-format clamp is strong yet light, with 2x spring loaded 2x steel alignment pins. The CNC machined e-coated knobs feature Teflon washers to stop binding. It also has a 1/4" UNC camera tripod thread on the underside, so you use it to mount your telescope on a camera tripod for casual stargazing, or daytime observation.
The Altair 60mm Miniguider probably needs no introduction. It's widely acclaimed for it's simplicity and accuracy, and is far easier to use than an Off-Axis-Guider (OAG) unit. It doesn't take up space in the imaging train, and require more adapters and calculations, nor does it cause flexure problems, due to it's unique locking focuser, with 3x clamping screws and brass insert. Selecting from a huge field of stars is easy at a very fast F3.75 so you don't need such a sensitive autoguider camera - and what's more, and theres no pickoff prism to intrude into the light-path of your full frame DSLR. Nor does it add flexure to the imaging train, or need to be frequently focused, unlike some cheap OAG units. Simply add your guide camera, set focus, and tighten the locking ring, and that's it. The Miniguider doesn't even need to point in exact the same direction as the main telescope so you can move it around in the (extremely unlikely) event you can't find a bright star.
The Starwave 200mm dovetail bar is strong, solid and more rigid than the cheap extruded rails often offered with guide-scope kits, and will fit the majority of mounts on the market.
* Do not be tempted to buy a finder-scope with a helical focuser for autoguiding. They focuser loses it's focus easily, and they aren't rigid enough for autoguiding due to the play in the helical mechanism. They are OK for eyepieces but not for autoguiding. We researched this thoroughly, and it's why we developed the superb Altair 1.25" locking focuser.
**Note Price Includes Shipping Cost**
Convert your Vixen-format mount to the wider 3" Losmandy-format dovetail with this conversion clamp. It fits the following mounts and more:
Skywatcher EQ5, EQ3-2
Vixen GP2, GPD2, SXW, SXD2
Meade & Celestron mounts with 1.75" dovetail bar
The Starwave Losmandy-format clamp is strong yet light, being spring loaded with 2x steel alignment pins. The 2x CNC machined e-coated knobs have teflon washers to stop binding.
Simply attach the Starwave Vixen to Losmandy Adapter to your Vixen-format mount using the 1.75" Vixen dovetail bar on the underside of the clamp.
The 3" Losmandy-format clamp can be separated from the Vixen-format 1.75" dovetail bar underneath by unfastening the hex bolts, and used separately.
**Note Price Includes Shipping Cost**
Regulated mains to 13.8v power supply with 1 x cigarette lighter socket and 2 x terminals
< 1 2 3 >
Terms and Conditions
Copyright ©2012 Ian King Imaging Ltd.
Site built by Savagescape Ltd.